| Citation ID |
01001A |
| Citaton Type |
Serious |
| Standard Cited |
19100028 B01 I A |
| Issuance Date |
2020-02-24 |
| Current Penalty |
1720.0 |
| Initial Penalty |
3441.0 |
| Final Order |
2020-03-18 |
| Nr Instances |
2 |
| Nr Exposed |
25 |
| Gravity |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.28(b)(1)(i)(A): The employer did not ensure that each employee on a walking-working surface with an unprotected side or edge that is 4 feet (1.2 m) or more above a lower level was protected from falling: a) Inside facility: On December 19, 2019 and at times prior thereto a guardrail system was not in place at the landing near the Verbruggen palletizer. This exposes employees to a 5 foot fall hazard. b) Outside facility: On December 19, 2019 and at times prior thereto a guardrail system was not in place along an area used by employees as a break area. This exposes employees to a 5 foot fall hazard. Note) Corrected during inspection. |
|
| Citation ID |
01001B |
| Citaton Type |
Serious |
| Standard Cited |
19100028 B03 V |
| Issuance Date |
2020-02-24 |
| Abatement Due Date |
2020-03-05 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2020-03-18 |
| Nr Instances |
1 |
| Nr Exposed |
25 |
| Gravity |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.28(b)(3)(v): (v) Each employee was not protected from falling through a hatchway and chute-floor hole: a) Facility: On December 19, 2019 and at times prior thereto employees were exposed to a floor hole adjacent to a walkway in the sorting and bagging room. The hole was part of a conveyor and chute system from the upper level to the lower level. Note) Certification of corrective action is required for this item. |
|
| Citation ID |
01001C |
| Citaton Type |
Serious |
| Standard Cited |
19100029 B02 I |
| Issuance Date |
2020-02-24 |
| Abatement Due Date |
2020-03-05 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2020-03-18 |
| Nr Instances |
1 |
| Nr Exposed |
1 |
| Gravity |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.29(b)(2)(i): (i) Midrails were not installed at a height midway between the top edge of the guardrail system and the walking-working surface: a) Inside facility: On December 19, 2019 and at times prior thereto a mid-rail was missing from a guardrail system located near the Onion Top Tail machine. Employees are exposed to a fall hazard when sweeping the area. Note) Abatement certification is required for this item. |
|
| Citation ID |
01002 |
| Citaton Type |
Serious |
| Standard Cited |
19100147 C01 |
| Issuance Date |
2020-02-24 |
| Abatement Due Date |
2020-08-03 |
| Current Penalty |
2700.0 |
| Initial Penalty |
5398.0 |
| Final Order |
2020-03-18 |
| Nr Instances |
1 |
| Nr Exposed |
1 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(1): The employer did not establish a program consisting of energy control procedures, employee training and periodic inspections to ensure that before any employee performs any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment would be isolated from the energy source and rendered inoperative: a) Facility: On December 19, 2019 and at times prior thereto the employer had not developed and implemented an energy control program with specific, written procedures, training for authorized and affected employees, and a periodic review of procedures and employees performance. Employees perform scheduled and unscheduled servicing and maintenance on machines including but not limited to the conveyor systems and the Onion Top Tail machine. Energy sources include but may not be limited to electric and hydraulic. Note) Certification of corrective action is required for this item. |
|
| Citation ID |
01003 |
| Citaton Type |
Serious |
| Standard Cited |
19100219 C02 I |
| Issuance Date |
2020-02-24 |
| Abatement Due Date |
2020-03-05 |
| Current Penalty |
2024.0 |
| Initial Penalty |
4048.0 |
| Final Order |
2020-03-18 |
| Nr Instances |
1 |
| Nr Exposed |
8 |
| Gravity |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.219(c)(2)(i): All exposed part(s) of horizontal shafting seven (7) feet or less from floor or working platform were not protected by stationary casing(s) enclosing shafting completely or by trough(s) enclosing sides and top or sides and bottom of shafting: a) Facility: On December 19, 2019 and at times prior thereto stationary guards were not in place for rotating horizontal shafts, including but may not be limited to areas on and around the sorting table, "jigger". This exposed employees to caught-by hazards. Note) Certification of corrective action is required for this item. |
|
| Citation ID |
01004A |
| Citaton Type |
Serious |
| Standard Cited |
19100219 D01 |
| Issuance Date |
2020-02-24 |
| Abatement Due Date |
2020-03-05 |
| Current Penalty |
2700.0 |
| Initial Penalty |
5398.0 |
| Final Order |
2020-03-18 |
| Nr Instances |
1 |
| Nr Exposed |
3 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.219(d)(1): Pulley(s) with part(s) seven feet or less from the floor or work platform were not guarded in accordance with the requirements specified in 29 CFR 1910.219(m) and (o): a) Facility: On December 19, 2109 and at times prior thereto employees were exposed to an unguarded belts and pulleys. This includes but may not be limited to belts and pulleys on the "colossal jigger" sorting machine. Note) Certification of corrective action is required for this item. |
|
| Citation ID |
01004B |
| Citaton Type |
Serious |
| Standard Cited |
19100219 F03 |
| Issuance Date |
2020-02-24 |
| Abatement Due Date |
2020-03-05 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2020-03-18 |
| Nr Instances |
1 |
| Nr Exposed |
3 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.219(f)(3): Sprocket wheels and chains which were seven -7 feet or less above floors or platforms were not enclosed: a) Facility: On December 19, 2019 and at times prior thereto chain and sprocket assemblies were not guarded. This included but may not be limited to, on the ground level of the bin dump machine. This exposes employees in the area to an ingoing nip point hazard. Note) Certification of corrective action is required for this item. |
|
| Citation ID |
02001 |
| Citaton Type |
Other |
| Standard Cited |
19040039 A02 |
| Issuance Date |
2020-02-24 |
| Abatement Due Date |
2020-02-28 |
| Current Penalty |
1000.0 |
| Initial Penalty |
6747.0 |
| Final Order |
2020-03-18 |
| Nr Instances |
1 |
| Nr Exposed |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1904.39(a)(2): The employer did not report to OSHA within twenty-four (24) hours after the in-patient hospitalization of one or more employees or an employee's amputation or an employee's loss of an eye resulting from a work-related incident: a) On December 19, 2019 the employer had not reported an employee injury which resulted in a fingertip amputation. The injury occurred on December 16, 2019. Note) Certification of abatement is not required for this item. |
|
| Citation ID |
02002 |
| Citaton Type |
Other |
| Standard Cited |
19100178 L06 |
| Issuance Date |
2020-02-24 |
| Abatement Due Date |
2020-04-09 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2020-03-18 |
| Nr Instances |
1 |
| Nr Exposed |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.178(l)(6): The employer did not certify that each operator has been trained and evaluated as required by this paragraph (l): a) Facility: On December 19, 2019 and at times prior thereto a powered industrial truck (forklift) operator had not been through the employer provided training for powered industrial trucks. This employee operates a forklift on a daily basis. Note) Certification of abatement is required for this item. |
|
