LATHAM CONSTRUCTION LLC

Inspection Type	Unprog Rel
Scope	Partial
Safety/Health	Safety
Close Conference	2022-03-17
Emphasis	L: FALL
Case Closed	2023-10-17

Related Activity

Type	Inspection
Activity Nr	1584309
Safety	Yes
Type	Inspection
Activity Nr	1584312
Safety	Yes

Violation Items

Citation ID	01001
Citaton Type	Serious
Standard Cited	19260501 B01
Issuance Date	2022-03-24
Abatement Due Date	2022-04-05
Current Penalty	4144.0
Initial Penalty	4144.0
Final Order	2022-10-07
Nr Instances	1
Nr Exposed	3
Gravity	5
FTA Current Penalty	0.0
Citation text line	29 CFR 1926.501(b)(1):Each employee on a walking/working surface with an unprotected side or edge which was 6 feet (1.8 m) or more above a lower level was not protected from falling by the use of guardrail systems, safety net systems, or personal fall arrest systems. (a) 600 E Riverside Drive, Eagle, ID 83616: On or about March 17, 2022, employees were exposed to falls of approximately 26-48 feet while performing roofing activities without fall protection. Note - Abatement certification is required for this item.

Inspection Type	Prog Other
Scope	Partial
Safety/Health	Safety
Close Conference	2020-11-02
Emphasis	N: CTARGET, P: CTARGET
Case Closed	2023-10-17

Related Activity

Type	Inspection
Activity Nr	1500442
Safety	Yes

Violation Items

Citation ID	01001
Citaton Type	Serious
Standard Cited	19260028 A
Issuance Date	2020-11-10
Current Penalty	1966.0
Initial Penalty	1966.0
Final Order	2021-01-05
Nr Instances	1
Nr Exposed	1
Gravity	1
FTA Current Penalty	0.0
Citation text line	29 CFR 1926.28(a): Appropriate personal protective equipment was not worn by employee(s) in all operations where there was exposure to hazardous conditions: a) Silverstone Apartments jobsite: On November 2, 2020 and at times prior thereto employees were not wearing safety glasses while performing siding activities using a pneumatic nail gun. Note) Corrected during inspection.

Inspection Type	Planned
Scope	Partial
Safety/Health	Safety
Close Conference	2018-11-01
Emphasis	N: CTARGET, P: CTARGET
Case Closed	2022-07-19

Related Activity

Type	Complaint
Activity Nr	1357756
Health	Yes
Type	Inspection
Activity Nr	1357756
Safety	Yes

Violation Items

Citation ID	01001A
Citaton Type	Serious
Standard Cited	19260020 B02
Issuance Date	2019-04-19
Abatement Due Date	2019-06-06
Current Penalty	3789.0
Initial Penalty	3789.0
Final Order	2019-06-27
Nr Instances	4
Nr Exposed	7
Gravity	5
FTA Current Penalty	0.0
Citation text line	29 CFR 1926.20(b)(2): The employer did not initiate and maintain a safety program which provides for frequent and regular inspections of jobsites, materials, and equipment to be made by a competent person: a) Jobsite: On November 1, 2018 and at times prior thereto; employer did not ensure that its siding employees were protected from electrical hazards; electrical cords attached to a radial saw, Skilsaw, and powerbox were found frayed and/or inadequately repaired. b) Outdoors: On November 1, 2018 and at times prior thereto; equipment operators used a DeWalt radial saw and Skilsaw to cut and rip Silica containing HardiePlank siding, but engineering controls were not in place, and a dust cloud was visible around the employee. Note* Abatement certification IS required for this item.
Citation ID	01001B
Citaton Type	Serious
Standard Cited	19261153 C01
Issuance Date	2019-04-19
Abatement Due Date	2019-08-30
Current Penalty	0.0
Initial Penalty	0.0
Final Order	2019-06-27
Nr Instances	1
Nr Exposed	2
Gravity	5
FTA Current Penalty	0.0
Citation text line	29 CFR 1926.1153(c)(1): For each employee engaged in a task identified on Table 1, the employer did not fully and properly implement the engineering controls, work practices, and respiratory protection specified for the task on Table 1, and did not assess and limit the exposure of the employee to respirable crystalline silica in accordance with paragraph (d) of this section. a) Outdoors: On or about November 1, 2018 and at times prior thereto; controlling employer did not ensure subcontractor's employees using a hand-held Skilsaw and Dewalt radial saw were using a dust collection control method to reduce silica containing cement fiber board - HardiePlank airborne particulate exposures. Note* Abatement certification IS required for this item.
Citation ID	01001C
Citaton Type	Serious
Standard Cited	19261153 F01
Issuance Date	2019-04-19
Abatement Due Date	2019-06-06
Current Penalty	0.0
Initial Penalty	0.0
Final Order	2019-06-27
Nr Instances	1
Nr Exposed	2
Gravity	5
FTA Current Penalty	0.0
Citation text line	29 CFR 1926.1153(f)(1): The employer allowed dry sweeping or dry brushing where such activity could contribute to employee exposure to respirable crystalline silica and wet sweeping, HEPA-filtered vacuuming or other methods were feasible: a) Outdoors: On or about November 1, 2018 and at times prior thereto; employees used a broom to sweep Silica containing HardiePlank dust; a thick collection of dust on the ground was visible below saw cutting surfaces, and the surrounding work areas which are not cleared on a daily basis. Note* Abatement certification IS required for this item.
Citation ID	01001D
Citaton Type	Serious
Standard Cited	19261153 G01
Issuance Date	2019-04-19
Abatement Due Date	2019-08-30
Current Penalty	0.0
Initial Penalty	0.0
Final Order	2019-06-27
Nr Instances	1
Nr Exposed	2
Gravity	5
FTA Current Penalty	0.0
Citation text line	29 CFR 1926.1153(g)(1): The employer did not establish and implement a written exposure control plan: a) Outdoors: On or about November 1, 2018 and at times prior thereto; Saw operators were cutting and ripping HardiePlank Silica containing siding with the use of a hand-held Skilsaw and Dewalt radial saw. Note* Abatement certification IS required for this item.
Citation ID	01001E
Citaton Type	Serious
Standard Cited	19100134 K06
Issuance Date	2019-04-19
Abatement Due Date	2019-08-30
Current Penalty	0.0
Initial Penalty	0.0
Final Order	2019-06-27
Nr Instances	1
Nr Exposed	2
Gravity	5
FTA Current Penalty	0.0
Citation text line	29 CFR 1910.134(k)(6): The employer did not provide the basic advisory information on respirators, as presented in Appendix D of 29 CFR 1910.134, in written or oral format to employees who wear respirators when such use was not required by the employer: (Construction Reference 1926.103): a) Outdoors: On or about November 5, 2018 and at times prior thereto; Saw operators were cutting and ripping HardiePlank Silica containing siding with the use of a hand-held Skilsaw and Dewalt radial saw while wearing an N95 dust mask with a beard. Note* Abatement certification IS required for this item.
Citation ID	01002A
Citaton Type	Serious
Standard Cited	19260403 A
Issuance Date	2019-04-19
Current Penalty	3031.0
Initial Penalty	3031.0
Final Order	2019-06-27
Nr Instances	3
Nr Exposed	8
Gravity	5
FTA Current Penalty	0.0
Citation text line	29 CFR 1926.403(a): All electrical conductors and equipment were not approved: a) Outdoors - Dewalt Chop Saw: On November 1, 2018 and at times prior thereto; damaged cords were not repaired to the state in which they were initially approved; strain relief. b) Outdoors - Skilsaw hand-held radial saw: On November 1, 2018 and at times prior thereto; frayed cord. Note* Abatement certification IS required for this item.
Citation ID	01002B
Citaton Type	Serious
Standard Cited	19260405 A02 II I
Issuance Date	2019-04-19
Current Penalty	0.0
Initial Penalty	0.0
Final Order	2019-06-27
Nr Instances	2
Nr Exposed	3
Gravity	5
FTA Current Penalty	0.0
Citation text line	29 CFR 1926.405(a)(2)(ii)(I): Flexible cords and cables used for temporary wiring were not protected from damage: a) Outdoors - Common Area in front of Buildings A and B: On November 1, 2018 and at times prior thereto; flexible cords attached to daily use equipment to included a Dewalt radial saw and hand-held Skilsaw were found frayed, repaired and strain relief did not fit securely. Note* Abatement certification IS required for this item.

Inspection Type	Referral
Scope	Partial
Safety/Health	Safety
Close Conference	2014-07-17
Emphasis	L: FALL, L: RESCON
Case Closed	2016-01-07

Related Activity

Type	Inspection
Activity Nr	985477
Safety	Yes
Type	Inspection
Activity Nr	985476
Safety	Yes
Type	Referral
Activity Nr	898792
Safety	Yes
Type	Inspection
Activity Nr	985473
Safety	Yes

Violation Items

Citation ID	01001
Citaton Type	Serious
Standard Cited	19260501 B13
Issuance Date	2014-07-31
Abatement Due Date	2014-08-06
Current Penalty	1600.0
Initial Penalty	1600.0
Final Order	2014-08-21
Nr Instances	1
Nr Exposed	2
Related Event Code (REC)	Referral
Gravity	5
FTA Current Penalty	0.0
Citation text line	29 CFR 1926.501(b)(13): Each employee engaged in residential construction activities 6 feet (1.8 m) or more above lower levels were not protected by guardrail systems, safety net system, or personal fall arrest system: a) Building 1585: On July 17, 2014 employees engaged in siding activities on a second floor balcony without a fall protection system in place. Note) Abatement certification IS required for this item.
Citation ID	01002
Citaton Type	Serious
Standard Cited	19261053 B13
Issuance Date	2014-07-31
Abatement Due Date	2014-08-06
Current Penalty	1200.0
Initial Penalty	1200.0
Final Order	2014-08-21
Nr Instances	1
Nr Exposed	1
Related Event Code (REC)	Referral
Gravity	1
FTA Current Penalty	0.0
Citation text line	29 CFR 1926.1053(b)(13): The top or top step of a stepladder was used as a step: a) Building 1585: On July 17, 2014 an employee stood on the top cap of an eight foot ladder to perform siding activities. Note) Abatement certification IS required for this item.
Citation ID	02001
Citaton Type	Other
Standard Cited	19260452 J02
Issuance Date	2014-07-31
Abatement Due Date	2014-08-06
Current Penalty	0.0
Initial Penalty	0.0
Final Order	2014-08-21
Nr Instances	1
Nr Exposed	1
Related Event Code (REC)	Referral
FTA Current Penalty	0.0
Citation text line	29 CFR 1926.452(j)(2): Poles were not secured to the structure by rigid triangular bracing or equivalent at the bottom, top, and other points as necessary: a) Building 1585: On July 17, 2014 the pump jack scaffold in use was not secured at the bottom. Note) Abatement certification IS required for this item.

Loan Status Date	2021-04-08
Loan Status	Paid in Full
Loan Maturity in Months	24
SBA Guaranty Percentage	100
Loan Approval Amount (at origination)	100110
Loan Approval Amount (current)	100110
Undisbursed Amount	0
Franchise Name	-
Lender Location ID	87893
Servicing Lender Name	Glacier Bank
Servicing Lender Address	202 Main St, KALISPELL, MT, 59901-4454
Rural or Urban Indicator	U
Hubzone	N
LMI	N
Business Age Description	Existing or more than 2 years old
Project Address	MERIDIAN, ADA, ID, 83642-4086
Project Congressional District	ID-01
Number of Employees	16
NAICS code	238990
Borrower Race	White
Borrower Ethnicity	Not Hispanic or Latino
Business Type	Limited Liability Company(LLC)
Originating Lender ID	87893
Originating Lender Name	Glacier Bank
Originating Lender Address	KALISPELL, MT
Gender	Male Owned
Veteran	Non-Veteran
Forgiveness Amount	100995.9
Forgiveness Paid Date	2021-03-10