|
346742497
|
1032500
|
2023-06-01
|
3555 HWY 95, NEW MEADOWS, ID, 83654
|
|
| Inspection Type |
Planned
|
| Scope |
Partial
|
| Safety/Health |
Safety
|
| Close Conference |
2023-06-01
|
| Emphasis |
L: FORKLIFT, P: FORKLIFT
|
| Case Closed |
2023-07-26
|
|
|
345144463
|
1032500
|
2021-02-10
|
3555 HWY 95, NEW MEADOWS, ID, 83654
|
|
| Inspection Type |
Referral
|
| Scope |
Partial
|
| Safety/Health |
Safety
|
| Close Conference |
2021-04-22
|
| Emphasis |
N: AMPUTATE
|
| Case Closed |
2021-08-24
|
Related Activity
| Type |
Referral |
| Activity Nr |
1726563 |
| Safety |
Yes |
|
Violation Items
| Citation ID |
01001 |
| Citaton Type |
Serious |
| Standard Cited |
19100265 C26 VIII |
| Issuance Date |
2021-06-03 |
| Abatement Due Date |
2021-10-01 |
| Current Penalty |
9400.0 |
| Initial Penalty |
13516.0 |
| Final Order |
2021-06-28 |
| Nr Instances |
1 |
| Nr Exposed |
5 |
| Related Event Code (REC) |
Referral |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.265(c)(26)(viii): Lower landing area(s) of stacker(s) and unstacker(s) were not guarded by enclosure(s) that prevented entrance to the area(s) or pit(s) below the hoist platform(s), nor were entrances protected by electrically interlocked gates which, when opened, disconnect the power and set the hoist brakes. a) Restacker Building: Employees are able to access the landing beneath an operating restacker between a railing and restacked lumber. b) Restacker Building: Employees are able to access the landing beneath the restacker through a gate that was not electrically interlocked. NOTE-Abatement documentation and certification are required for this item. |
|
| Citation ID |
02001 |
| Citaton Type |
Repeat |
| Standard Cited |
19100219 F03 |
| Issuance Date |
2021-06-03 |
| Abatement Due Date |
2021-08-02 |
| Current Penalty |
20300.0 |
| Initial Penalty |
27033.0 |
| Final Order |
2021-06-28 |
| Nr Instances |
1 |
| Nr Exposed |
5 |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.219(f)(3): Sprocket wheels and chains which were seven (7) feet or less above floors or platforms were not enclosed. a) Restacker: A restacker chain and sprocket, approximately 6 feet from the ground was unguarded. Employees are within 12 inches of the chain and sprocket when they are in the lower landing. b) Restacker: A restacker chain and sprocket, approximately 6 feet from the ground, and level with the upper level walkway, was unguarded. Employees are within 12 inches of the chain and sprocket when standing on the upper level walkway. Tamarack Mill LLC dba Evergreen Forest was previously cited for a Serious violation of this occupational safety and health standard, 29 CFR 1910.219(f)(3), which was contained in OSHA inspection number 1282735, citation number 2, item number 2 and was affirmed as a final order on March 20, 2018, with respect to a workplace located at 3555 Hwy 95, New Meadows, ID 83654. NOTE-Abatement documentation and certification are required for this item. |
|
|
|
343884771
|
1032500
|
2019-03-27
|
3555 HWY 95, NEW MEADOWS, ID, 83654
|
|
| Inspection Type |
FollowUp
|
| Scope |
Partial
|
| Safety/Health |
Safety
|
| Close Conference |
2019-03-27
|
| Case Closed |
2019-09-26
|
Related Activity
| Type |
Inspection |
| Activity Nr |
1282735 |
| Safety |
Yes |
|
Violation Items
| Citation ID |
01001 |
| Citaton Type |
Serious |
| Standard Cited |
19260501 B01 |
| Issuance Date |
2019-05-15 |
| Abatement Due Date |
2019-06-11 |
| Current Penalty |
4508.0 |
| Initial Penalty |
4508.0 |
| Final Order |
2019-06-19 |
| Nr Instances |
2 |
| Nr Exposed |
1 |
| Related Event Code (REC) |
Referral |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1926.501(b)(1): Each employee on a walking/working surface with an unprotected side or edge which was 6 feet (1.8 m) or more above a lower level was not protected from falling by the use of guardrail systems, safety net systems, or personal fall arrest systems. (a) New Edger Line: On or about March 27, 2019 and at times prior, an employee was exposed to a 13 ft. fall while removing second floor decking. (b) North Side of Building: On or about March 27, 2019 and at times prior, an employee was exposed to an approximately 12 ft. fall while disposing of second floor decking. Note: Abatement certification is required for this item. |
|
|
|
342827359
|
1032500
|
2017-12-12
|
3555 HWY 95, NEW MEADOWS, ID, 83654
|
|
| Inspection Type |
Referral
|
| Scope |
Partial
|
| Safety/Health |
Safety
|
| Close Conference |
2017-12-12
|
| Emphasis |
N: AMPUTATE
|
| Case Closed |
2019-03-18
|
Related Activity
| Type |
Referral |
| Activity Nr |
1290546 |
| Safety |
Yes |
|
Violation Items
| Citation ID |
01001 |
| Citaton Type |
Serious |
| Standard Cited |
19100147 C07 I |
| Issuance Date |
2018-03-06 |
| Abatement Due Date |
2018-05-01 |
| Current Penalty |
6000.0 |
| Initial Penalty |
9959.0 |
| Final Order |
2018-03-20 |
| Nr Instances |
1 |
| Nr Exposed |
96 |
| Related Event Code (REC) |
Accident |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(7)(i): The employer did not provide training to ensure that the purpose and function of the energy control program are understood by employees and that the knowledge and skills required for the safe application, usage, and removal of the energy controls are acquired by employees: a) On December 7, 2017 and times prior thereto, employees performed repairs on the Chipper Blower without being trained on lock out tag out. Note: Abatement certification and documentation is required for this item. |
|
| Citation ID |
01002A |
| Citaton Type |
Serious |
| Standard Cited |
19100028 B03 II |
| Issuance Date |
2018-03-06 |
| Abatement Due Date |
2018-03-30 |
| Current Penalty |
4000.0 |
| Initial Penalty |
8536.0 |
| Final Order |
2018-03-20 |
| Nr Instances |
1 |
| Nr Exposed |
96 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.28(b)(3)(ii): The employer did not ensure each employee is protected from tripping into or stepping into or through any hole that is less than 4 feet (1.2 m) above a lower level by covers or guardrail systems: (a) Board Edger Area: On December 7, 2017 and times prior thereto, employees are exposed to a 14 inch by 14 inch hole in the walkway. Note: Abatement certification is required for this item. |
|
| Citation ID |
01002B |
| Citaton Type |
Serious |
| Standard Cited |
19100265 C04 II |
| Issuance Date |
2018-03-06 |
| Abatement Due Date |
2018-03-30 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2018-03-20 |
| Nr Instances |
1 |
| Nr Exposed |
96 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.265(c)(4)(ii): Walkway(s) were not evenly floored: (a) Board Edger Area: On December 7, 2017 and times prior thereto, employees work on floors that are damaged. Note: Abatement certification is required for this item. |
|
| Citation ID |
02001A |
| Citaton Type |
Repeat |
| Standard Cited |
19100147 C04 I |
| Issuance Date |
2018-03-06 |
| Abatement Due Date |
2018-05-01 |
| Current Penalty |
40000.0 |
| Initial Penalty |
49796.0 |
| Final Order |
2018-03-20 |
| Nr Instances |
1 |
| Nr Exposed |
4 |
| Related Event Code (REC) |
Accident |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: a) On December 7, 2017 and times prior thereto, specific, written procedures for the control of all potential sources of hazardous energy were not utilized or enforced for the protection of employees who perform scheduled and unscheduled maintenance on machinery. Machinery includes, but is not limited to, maintenance and cleaning of the board edger. Tamarack Mill, LLC dba Evergreen Forest was previously cited at Tamarack Mill, LLC dba Clearwater Forest Industries, for a REPEAT violation of this occupational safety and health standard, 29 CFR 1910.147(c)(4)(i), which was contained in OSHA inspection number 1232711, citation number 2, item number 1, and was affirmed as a final order on August 17, 2017, with respect to a workplace located at 4686 Hwy 13 S, Kooskia, ID 83539. Evergreen Mill, LLC dba Clearwater Forest Industries was previously cited at Evergreen Mill, LLC dba Clearwater Forest Industries, for a REPEAT violation of this occupational safety and health standard, 29 CFR 1910.147(c)(4)(i), which was contained in OSHA inspection number 984232, citation number 2, item number 2a, and was affirmed as a final order on December 12, 2014, with respect to a workplace located at 4686 Hwy 13 S, Kooskia, ID 83539. Evergreen Mill, LLC dba Clearwater Forest Industries was previously cited at Tamarack Mill LLC dba Evergreen Forest, for a Serious violation of this occupational safety and health standard, 29 CFR 1910.147(c)(4)(i), which was contained in OSHA inspection number 915674, citation number 2, item number 1 and was affirmed as a final order on October 30, 2013, with respect to a workplace located at 3555 Hwy 95, New Meadows, ID 83654. Note: Certification AND documentation of corrective action are required for this item. |
|
| Citation ID |
02001B |
| Citaton Type |
Repeat |
| Standard Cited |
19100147 C07 IV |
| Issuance Date |
2018-03-06 |
| Abatement Due Date |
2018-05-01 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2018-03-20 |
| Nr Instances |
3 |
| Nr Exposed |
96 |
| Related Event Code (REC) |
Accident |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(7)(iv): The employer did not certify that employee training had been accomplished and was being kept up to date: (a) On December 7, 2017 and times prior thereto, board edger operators perform lock out tag out of board edger without being LOTO trained. (b) On December 7, 2017 and times prior thereto, maintenance employees perform lock out tag out of board edger without being LOTO trained. (a) On December 7, 2017 and times prior thereto, clean up employees perform lock out tag out of board edger without being LOTO trained. Evergreen Mill, LLC dba Clearwater Forest Industries was previously cited at Evergreen Mill, LLC dba Clearwater Forest Industries, for a REPEAT violation of this occupational safety and health standard, 29 CFR 1910.147(c)(7)(iv), which was contained in OSHA inspection number 984232, citation number 2, item number 2c, and was affirmed as a final order on December 12, 2014, with respect to a workplace located at 4686 Hwy 13 S, Kooskia, ID 83539. Evergreen Mill, LLC dba Clearwater Forest industries was previously cited at their sister location, Tamarack Mill, LLC dba Evergreen Forest, for a violation of this occupational safety and health standard 29 1910.147(c)(7)(iv), which was contained in OSHA inspection number 915674, citation number 1, item number 4b, and was affirmed as a final order on October 30, 2013, with respect to a workplace located at 3555 Hwy 95, New Meadows, ID 83654. Note: Abatement certification AND documentation are required for this item. |
|
| Citation ID |
02002 |
| Citaton Type |
Repeat |
| Standard Cited |
19100219 F03 |
| Issuance Date |
2018-03-06 |
| Abatement Due Date |
2018-03-30 |
| Current Penalty |
19918.0 |
| Initial Penalty |
19918.0 |
| Final Order |
2018-03-20 |
| Nr Instances |
1 |
| Nr Exposed |
4 |
| Related Event Code (REC) |
Accident |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.219(f)(3): Sprocket wheels and chains which were seven 7 feet or less above floors or platforms were not enclosed: (a) On December 7, 2017 and times prior thereto, the approximately 8 inch diameter sprocket on the trimmer and vertical table that was approximately 3 feet from the floor was not guarded. Evergreen Mill, LLC dba Clearwater Forest Industries was previously cited at Tamarack Mill LLC dba Evergreen Forest, for a Serious violation of this occupational safety and health standard, 29 CFR 1910.219(f)(3), which was contained in OSHA inspection number 915674, citation number 1, item number 5 and was affirmed as a final order on October 30, 2013, with respect to a workplace located at 3555 Hwy 95, New Meadows, ID 83654. Note: Abatement certification AND documentation are required for this item. |
|
|
|
342327111
|
1032500
|
2017-05-11
|
HIGHWAY 13 SOUTH, KOOSKIA, ID, 83539
|
|
| Inspection Type |
Referral
|
| Scope |
Partial
|
| Safety/Health |
Safety
|
| Close Conference |
2017-05-11
|
| Emphasis |
N: AMPUTATE
|
| Case Closed |
2018-09-27
|
Related Activity
| Type |
Referral |
| Activity Nr |
1210537 |
| Safety |
Yes |
|
Violation Items
| Citation ID |
01001 |
| Citaton Type |
Serious |
| Standard Cited |
19100133 A02 |
| Issuance Date |
2017-07-19 |
| Abatement Due Date |
2017-08-14 |
| Current Penalty |
1700.0 |
| Initial Penalty |
3232.0 |
| Final Order |
2017-08-17 |
| Nr Instances |
1 |
| Nr Exposed |
1 |
| Gravity |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.133(a)(2): The employer did not ensure that each affected employee used eye protection that provided side protection when there was a hazard from flying objects. (a) Planer room: On and before May 10, 2017 employees working in the planer room during upset conditions were not wearing eye protection with side shields. Note: Abatement certification is required for this item |
|
| Citation ID |
01002 |
| Citaton Type |
Serious |
| Standard Cited |
19100265 E06 I A |
| Issuance Date |
2017-07-19 |
| Abatement Due Date |
2017-09-15 |
| Current Penalty |
6500.0 |
| Initial Penalty |
8873.0 |
| Final Order |
2017-08-17 |
| Nr Instances |
1 |
| Nr Exposed |
2 |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.265(e)(6)(i)(a): Cutting head(s) on planner(s) were not guarded: (a) Planer room: On an before May 8, 2017 employees clearing jams during upset conditions were not adequately protected from contact with rotary knives on the top head of the planer. Note: Abatement certification and documentation ARE required for this item. |
|
| Citation ID |
02001 |
| Citaton Type |
Repeat |
| Standard Cited |
19100147 C04 I |
| Issuance Date |
2017-07-19 |
| Abatement Due Date |
2017-09-15 |
| Current Penalty |
33000.0 |
| Initial Penalty |
44363.0 |
| Final Order |
2017-08-17 |
| Nr Instances |
1 |
| Nr Exposed |
2 |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section. (a) Planer room: On and before May 10, 2017, employees who perform scheduled and unscheduled maintenance on the Newman planer, did they recognize and/or acknowledge the hazards of clearing jammed equipment without first positively controlling all energy sources. Evergreen Mill, LLC dba Clearwater Forest Industries was previously cited at Tamarack Mill, LLC dba Evergreen Forest, for a REPEAT violation of this occupational safety and health standard, 29 CFR 1910.147(c)(4)(i), which was contained in OSHA inspection number 984232, citation number 2, item number 2a, and was affirmed as a final order on December 12, 2014, with respect to a workplace located at 3555 Hwy 95, New Meadows, ID 83654. Evergreen Mill, LLC dba Clearwater Forest Industries was previously cited at Tamarack Mill LLC dba Evergreen Forest, for a Serious violation of this occupational safety and health standard, 29 CFR 1910.147(c)(4)(i), which was contained in OSHA inspection number 915674, citation number 2, item number 1 and was affirmed as a final order on October 30, 2013, with respect to a workplace located at 3555 Hwy 95, New Meadows, ID 83654. Note: Abatement certification and documentation is required for this item. |
|
|
|
339156747
|
1032500
|
2013-06-24
|
3555 HWY 95, NEW MEADOWS, ID, 83654
|
|
| Inspection Type |
Complaint
|
| Scope |
Complete
|
| Safety/Health |
Safety
|
| Close Conference |
2013-06-25
|
| Emphasis |
L: FORKLIFT
|
| Case Closed |
2013-11-15
|
Related Activity
| Type |
Complaint |
| Activity Nr |
823768 |
| Safety |
Yes |
| Health |
Yes |
|
| Type |
Inspection |
| Activity Nr |
915705 |
| Safety |
Yes |
|
Violation Items
| Citation ID |
01001A |
| Citaton Type |
Serious |
| Standard Cited |
19100022 A01 |
| Issuance Date |
2013-09-27 |
| Abatement Due Date |
2013-10-24 |
| Current Penalty |
2680.0 |
| Initial Penalty |
4900.0 |
| Final Order |
2013-11-14 |
| Nr Instances |
1 |
| Nr Exposed |
35 |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.22(a)(1): All places of employment, passageways, storerooms, and service rooms were not kept clean and orderly and in a sanitary condition: a) Chipper Room: On June 24, 2013, and at times prior thereto, more than 5% of the total square footage of the floor and horizontal surfaces were covered in combustible and explosive wood dust measuring at least 1/32 inch. Note: Abatement certification and documentation ARE required for this item. |
|
| Citation ID |
01001B |
| Citaton Type |
Serious |
| Standard Cited |
19100265 C20 III |
| Issuance Date |
2013-09-27 |
| Abatement Due Date |
2013-10-24 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2013-11-14 |
| Nr Instances |
1 |
| Nr Exposed |
35 |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.265(c)(20)(iii): Each woodworking machine that creates dust, shavings, chips, or slivers was not equipped with an exhaust or conveyor system located and adjusted to remove the maximum amount of refuse from the point of operation and immediate vicinity: a) Throughout the mill: On June 24, 2013, and at times prior thereto, the exhaust systems were not adjusted to remove the maximum amount of wood dust allowing it to accumulate on the floor and horizontal surfaces to depth greater than 1/32 inch. Note: Abatement certification and documentation ARE required for this item. |
|
| Citation ID |
01001C |
| Citaton Type |
Serious |
| Standard Cited |
19100307 C |
| Issuance Date |
2013-09-27 |
| Abatement Due Date |
2013-10-24 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2013-11-14 |
| Nr Instances |
1 |
| Nr Exposed |
35 |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.307(c): Electrical installations. Equipment, wiring methods, and installations of equipment in hazardous (classified) locations were not intrinsically safe, approved for the hazardous (classified) location, or safe for the hazardous (classified) location: a) On June 24, 2013, and at times prior thereto, not all electrical equipment had been evaluated for the hazard classification of Class II for the combustible dust hazard present in the throughout the workplace. Note: Abatement certification and documentation ARE required for this item. |
|
| Citation ID |
01002 |
| Citaton Type |
Serious |
| Standard Cited |
19100023 A08 II |
| Issuance Date |
2013-09-27 |
| Current Penalty |
1500.0 |
| Initial Penalty |
2975.0 |
| Final Order |
2013-11-14 |
| Nr Instances |
1 |
| Nr Exposed |
1 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.23(a)(8)(ii): A floor hole cover of standard strength and construction was not in place, the floor hole was not constantly attended by someone or was not protected by a removable standard railing: (a) In the Mill at the DA edger, On June 24, 2013, and at times prior thereto, employees were exposed to a fall hazard when walking/ working at the NE end of the edger where the sawdust hole was open and un-protected. Note: Abatement certification is NOT required for this item. |
|
| Citation ID |
01003A |
| Citaton Type |
Serious |
| Standard Cited |
19100023 D01 III |
| Issuance Date |
2013-09-27 |
| Abatement Due Date |
2013-10-24 |
| Current Penalty |
1800.0 |
| Initial Penalty |
3570.0 |
| Final Order |
2013-11-14 |
| Nr Instances |
1 |
| Nr Exposed |
3 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.23(d)(1)(iii): Stairs with four or more risers and less than 44 inches wide with both sides open did not have one stair railing on each side: a) In the mill at the DA edger, On June 24, 2013, and at times prior thereto, the five stairs at the DS edger out feed conveyor had no hand rails. Note: Abatement certification IS required. |
|
| Citation ID |
01003B |
| Citaton Type |
Serious |
| Standard Cited |
19100024 D |
| Issuance Date |
2013-09-27 |
| Abatement Due Date |
2013-10-24 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2013-11-14 |
| Nr Instances |
1 |
| Nr Exposed |
2 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.24(d): Fixed stairways were not a minimum width of 22 inches: (a) In the Mill at the DA edger, On June 24, 2013, and at times prior thereto, the flight of 5 stairs up to the out feed conveyor was only 18 inches wide. Note: Abatement certification IS required for this item. |
|
| Citation ID |
01003C |
| Citaton Type |
Serious |
| Standard Cited |
19100024 F |
| Issuance Date |
2013-09-27 |
| Abatement Due Date |
2013-10-24 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2013-11-14 |
| Nr Instances |
2 |
| Nr Exposed |
5 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.24(f): All stair rise height and tread width were not uniform throughout any flight of stairs including any foundation structure used as one or more treads of the stairs: (a) In the Mill at the DA edger, On June 24, 2013, and at times prior thereto, the rise of each stair was not uniform from the walking surface to the top landing, the three steps had a rise of 7;9;9 inches respectively. (b) In the Mill at the DA edger, On June 24, 2013, and at times prior thereto, the rise of each stair was not uniform from the walking surface to the top landing, the two steps had a rise of 6; 8.5 inches respectively. Note: Abatement certification IS required for this item. |
|
| Citation ID |
01003D |
| Citaton Type |
Serious |
| Standard Cited |
19100024 I |
| Issuance Date |
2013-09-27 |
| Abatement Due Date |
2013-10-24 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2013-11-14 |
| Nr Instances |
1 |
| Nr Exposed |
3 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.24(i): Vertical clearance above any stair tread to an overhead obstruction was not at least 7 feet measured from the leading edge of the tread: (a) In the Mill at the DA edger, On June 24, 2013, and at times prior thereto, second floor exterior of the DA edger the "roof" over the tie control console was only six feet above the walking working surface and the effective height of the at the stair nose was 5 feet 4 3/4 inches. Note: Abatement certification IS required for this item. |
|
| Citation ID |
01004A |
| Citaton Type |
Serious |
| Standard Cited |
19100147 C06 II |
| Issuance Date |
2013-09-27 |
| Abatement Due Date |
2013-10-24 |
| Current Penalty |
2680.0 |
| Initial Penalty |
4900.0 |
| Final Order |
2013-11-14 |
| Nr Instances |
1 |
| Nr Exposed |
3 |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(6)(ii): The employer did not certify that the periodic inspections have been performed. The certification did not identify the machine or equipment on which the energy control procedure was being utilized, the date of the inspection, the employees included in the inspection, and the person performing the inspection: (a) On or about June 24, 2013, and at times prior thereto, the employer did not conduct or certify that management had observed employees performing lock out or tag out procedures. Note: Abatement certification and documentation ARE required for this item. |
|
| Citation ID |
01004B |
| Citaton Type |
Serious |
| Standard Cited |
19100147 C07 IV |
| Issuance Date |
2013-09-27 |
| Abatement Due Date |
2013-10-24 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2013-11-14 |
| Nr Instances |
1 |
| Nr Exposed |
3 |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(7)(iv): The employer did not certify that employee training has been accomplished and is being kept up to date. The certification shall contain each employee's name and dates of training: (a) On or about June 24, 2013, and at times prior thereto, the employer could not provide certification that employees that were re-aligning the lumber carrying chain had been trained in lock out tag out requirements. Note: Abatement certification and documentation ARE required for this item. |
|
| Citation ID |
01004C |
| Citaton Type |
Serious |
| Standard Cited |
19100147 D04 I |
| Issuance Date |
2013-09-27 |
| Abatement Due Date |
2013-10-24 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2013-11-14 |
| Nr Instances |
1 |
| Nr Exposed |
3 |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(d)(4)(i): Lockout or tag out devices were not affixed to each energy isolating device by authorized employees: (a) At the sorter stacker: on or about June 24, 2013, and at times prior thereto, all employees who were clearing a jam and realigning the chain on the sorter stacker had not locked out the equipment or tagged out the equipment while they were exposed to the hazard of unexpected start up and movement of the chains. Note: Abatement certification and documentation ARE required for this item. |
|
| Citation ID |
01005 |
| Citaton Type |
Serious |
| Standard Cited |
19100219 F03 |
| Issuance Date |
2013-09-27 |
| Abatement Due Date |
2013-10-24 |
| Current Penalty |
1500.0 |
| Initial Penalty |
2975.0 |
| Final Order |
2013-11-14 |
| Nr Instances |
3 |
| Nr Exposed |
3 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.219(f)(3): All sprocket wheels and chains were not enclosed unless they were more than seven (7) feet above the floor or platform. Where the drive extends over other machine or working areas, protection against falling were not provided: a) On or about June 24, 2013, and at times prior thereto, the pinch point at the drive roller on the West side of the DA edger was unguarded. b) On or about June 24, 2013, and at times prior thereto, pinch points right of the DA edger operator station were unguarded. c) On or about June 24, 2013, and at times prior thereto, pinch points on the north side of the auto edger out feed belt were unguarded. Note: Abatement certification IS required for this item. |
|
| Citation ID |
02001 |
| Citaton Type |
Repeat |
| Standard Cited |
19100147 C04 I |
| Issuance Date |
2013-09-27 |
| Abatement Due Date |
2013-10-24 |
| Current Penalty |
3150.0 |
| Initial Penalty |
4200.0 |
| Final Order |
2013-11-14 |
| Nr Instances |
3 |
| Nr Exposed |
10 |
| Gravity |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees are engaged in the activities covered by this section: a) In the mill, On June 24, 2013, and at times prior thereto, specific lock out tag out procedures were not developed, and implemented for tasks such as changing the vertical resaw. b) In the mill, On June 24, 2013, and at times prior thereto, specific lock out tag out procedures were not developed, and implemented for tasks such as clearing jams from the sorter stacker lines. c) In the mill, On June 24, 2013, and at times prior thereto, specific lock out tag out procedures were not developed, and implemented for tasks such as clearing plugs at the chipper room. Note: Abatement certification and documentation ARE required for this item. Clearwater Forest Industries, Inc. dBA Evergreen Forest was previously cited for a violation of this occupational safety and health standard or its equivalent standard 29 CFR 1910.147(c)(4)(i), which was contained in OSHA inspection number 311580807, citation number 02, item number 002 and was affirmed as a final order on April 15, 2009, with respect to a workplace located at Highway 13 South, Kooskia, ID 83539. |
|
| Citation ID |
02002 |
| Citaton Type |
Repeat |
| Standard Cited |
19100219 C04 I |
| Issuance Date |
2013-09-27 |
| Abatement Due Date |
2013-10-24 |
| Current Penalty |
7350.0 |
| Initial Penalty |
9800.0 |
| Final Order |
2013-11-14 |
| Nr Instances |
5 |
| Nr Exposed |
10 |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.219(c)(4)(i): Unguarded shaft ends projected more than one-half the diameter of the shaft: a) On or about June 24, 2013, and at times prior thereto, shafts ends to the right of the DA edger operators station were unguarded. b) On or about June 24, 2013, and at times prior thereto, shaft ends on the roll case on the N side of the DA edger were unguarded and exceeded one half the diameter of the shaft. c) On or about June 24, 2013, and at times prior thereto, shafts were unguarded in front of the operator station of the DA edger. d) On or about June 24, 2013, and at times prior thereto, the shaft ends at the drive roller on the West side of the DA edger were unguarded. e) On or about June 24, 2013, and at times prior thereto, shaft ends on the press roll at the auto edger were unguarded. Note: Abatement certification and documentation ARE required for this item. Clearwater Forest Industries, Inc. dBA Evergreen Forest was previously cited for a violation of this occupational safety and health standard or its equivalent standard 29 CFR 1910.219(c)(4)(i) which was contained in OSHA inspection number 311580807, citation number 01, item number 003a and was affirmed as a final order on April 15, 2009, with respect to a workplace located at Highway 13 South, Kooskia, ID. |
|
| Citation ID |
03001 |
| Citaton Type |
Other |
| Standard Cited |
19100132 H01 |
| Issuance Date |
2013-09-27 |
| Abatement Due Date |
2013-10-24 |
| Current Penalty |
0.0 |
| Initial Penalty |
1000.0 |
| Final Order |
2013-11-14 |
| Nr Instances |
1 |
| Nr Exposed |
96 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.132(h)(1): Personal protective equipment (PPE), used to comply with this part, was not provided by the employer at no cost to employees: a) In the mill, On June 24, 2013, and at times prior thereto, the employer required employees to purchase personal protective equipment such as gloves. Note: Abatement certification IS required for this item. |
|
| Citation ID |
03002 |
| Citaton Type |
Other |
| Standard Cited |
19100305 B02 I |
| Issuance Date |
2013-09-27 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2013-11-14 |
| Nr Instances |
1 |
| Nr Exposed |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.305(b)(2)(i): All pull boxes, junction boxes, and fittings were not provided with covers identified for the purpose: (a) Chipper building, on or about June 24, 2013, and at times prior thereto, 110 volt mercury switch electrical box was missing its cover. Note: Abatement certification is NOT required for this item. |
|
| Citation ID |
03003 |
| Citaton Type |
Other |
| Standard Cited |
19101200 E01 I |
| Issuance Date |
2013-09-27 |
| Abatement Due Date |
2013-10-24 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2013-11-14 |
| Nr Instances |
1 |
| Nr Exposed |
96 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.1200(e)(1)(i): Employer did not develop, implement, and maintain a list of the hazardous chemicals known to be present using a product identifier that is referenced on the appropriate safety data sheet (the list may be compiled for the workplace as a whole or for individual work areas); a) On or before June 24, 2013, and at times prior thereto, the employer did not have a list of chemicals, found and used in the work place such as paint and solvent. Note: Abatement certification IS required for this item. |
|
|
